多試樣橡膠低溫脆性試驗機的試驗標準：

1.規格

試樣的長為25.0±0.5mm，寬為6.0±0.5mm，厚為2.0±0.3mm。

2.要求

試樣的表面應光滑，無外來雜質及損傷。成品應經打磨后裁制成相應尺寸。

多試樣橡膠低溫脆性試驗機的使用方法:

1.接通電源，溫控儀和計時器顯示燈亮。

2.向冷井中注入冷凍介質（一般為工業乙醇），其注入量應保證夾持器的下端到液面的距離為75±10mm。

3.將試樣垂直夾在夾持器上。夾的不宜過緊或過松，以防止試樣變形或脫落。

4.達到試驗溫度后，按下啟動按鈕，試驗機自動工作（按下夾持器，開始冷凍試樣，同時啟動時序控制開關或按動秒表計時。試樣冷凍時間規定為3.0±0.5min。試樣冷凍期間，冷凍介質溫度波動不得超過±1℃）

5.取下試樣，將試樣按沖擊方向彎曲成180°，仔細觀察有無破壞。

6.試樣經沖擊后（每個試樣只準沖擊一次），如出現破壞時，應提高冷凍介質的溫度，否則降低其溫度，繼續進行試驗。

7.溫度調節方法：

a、按set鍵，溫控儀進入設置狀態

b、按“＜”鍵移動到要設置的位置

c、按“∧”鍵調整溫度

d、按“set”鍵確定

通過反復試驗，確定至少有兩個試樣不破壞的低溫度和至少一個試樣破壞的gao溫度，如這兩個結果相差不大于1℃時，即試驗結束。

Technical parameters:1. Temperature Control Range: Room Temperature-70 C (Room Temperature < 25 C)    2. Constant temperature accuracy: +0.3 C     3. Cooling rate: 0 ~30 ~2.5 C/min   &nbsp;From -30 to -40 degrees Celsius, about 2.5 degrees Celsius/min     From - 40 to - 70 degrees centigrade, about 2.0 degrees centigrade/min      4. Maximum shape size: 900 *500 *800mm (length *width *height)     5. Effective workspace of studio: 280 *170 *120mm (length *width *height)    6. Quantity of packable specimens: 1     7. Digital timer digital timer: 0 seconds - 99 minutes, resolution 1 second     8. Cooling medium: ethanol or other non-freezing liquid        9. Stirring motor: 8W       10. Working power supply: 220V-240V, 50Hz, 1.5kW         11. Working temperature: <25 C

儀器標準：本儀器是根據GB1682標準設計的，各項技術指標符合HG 2-162-1965塑料低溫沖擊壓縮試驗方法和GB5470-2008 塑料沖擊脆化溫度試驗方法等標準的要求。

Instrument standards:The instrument is designed according to GB1682 national standard. The technical indexes meet the requirements of HG 2-162-1965 low temperature impact compression test method and GB5470-2008 plastic impact embrittlement temperature test method.

Structural principle：A. The equipment consists of the main body of the refrigeration compressor, heating device, electronic control box, cooling tank, cooling medium circulation system and automatic alarm device. After starting the refrigeration switch, the compressor starts to work and the refrigeration system enters the formal working state. The refrigeration compressor works continuously. When approaching the set temperature, the heating device in the cooling tank begins to provide heat proportionally to balance the excess cold generated by the refrigeration system in order to achieve the goal of constant temperature. Stirring can make the cooling medium in the cooling tank circulate continuously and make the temperature uniform.   B. Sample holder      Four specimens (rubber) are clamped on one side and fifteen specimens (plastic) are clamped on the other.    C. Impulse Device     The impact device consists of an impact hammer and a self-locking mechanism.      D. impactor    The radius of the impact head is 1.6 + 0.1 mm.  When impacting, the gap between the impacting head and the sample holder is 6.4 + 0.3 mm.     The distance between the center line of the impact head and the sample holder is 8 +0.3mm.

特點及用途:低溫脆性試驗機是測定材料在規定條件下試樣受沖擊出現破壞時的高溫度，即為脆性溫度，可以對塑料及其他彈性材料在低溫條件下的使用性能作比較性鑒定。可以測定不同橡膠材料或不同配方的硫化橡膠的脆性溫度和低溫性能的優劣。因此無論在科學研究材料及其制品的質量檢驗，生產過程的控制等方面均是*的。

適用行業：可以用來考核和確定電工、電子、汽車電器、材料等產品，在低溫環境條件下貯存和使用的適應性，適用于學校，工廠，，研位，等單位。

Usage: 1. Switch on the power supply, the temperature controller and the timer display light are on. 2. To inject refrigerant (industrial ethanol) into the cold well, the injection quantity should ensure that the distance from the lower end of the clamp to the liquid level is 75 +10 mm. 3. Hold the sample vertically on the clamp. The clamp should not be too tight or loose to prevent the specimen from deforming or falling off. 4. Press the gripper and start to freeze the sample. At the same time, start the timing control switch (or press the stopwatch) to time. The freezing time of the sample is 3.0 +0.5 min. During the freezing period of the sample, the temperature fluctuation of the refrigerant must not exceed (+1 C). 5. Lift the lifting clamp so that the impactor impacts the specimen in half a second. 6. Take down the sample and bend it to 180 degrees in the direction of impact. Carefully observe whether there is any damage. 7. After impact (each specimen is allowed to impact only once), if damage occurs, the temperature of the refrigerant should be increased, otherwise the temperature of the refrigerant should be lowered and the test should be continued. Temperature, if the difference between the two results is not more than 1 C, is the end of the test.  

Notes 1. The cooling cycle should not be cut off during the test, otherwise the cooling effect will be produced. 2. The cylinder pressure has been adjusted before leaving the factory and can not be changed arbitrarily.

使用者的維護：為了防止意外發生，請不要接觸機內部件。本機器內部所有的零件，不需使用者的維護。如果機器有異常情況發生，請直接與北廣精儀公司廠家或其的經銷商給予維護。

使用者的修改：使用者不得自行更改機器的線路或零件，如被更改機器后保修則自動失效并且本公司不負任何事故責任。在保修內使用未經我公司認可的零件或附件造成故障也不予保證。如發現送回檢修的機器被更改，將機器的電路和零件修復回原來設計的狀態，并收取修護費用。

我廠主要產品有：萬能材料試驗機，海綿泡沫落球回彈試驗機，海綿泡沫壓陷硬度測驗儀，海綿泡沫切割機，海綿泡沫疲勞壓陷試驗機，熔融指數儀，塑料滑動摩擦磨損試驗機，電壓擊穿試驗儀，塑料球壓痕硬度計，馬丁耐熱試驗儀，海綿泡沫拉伸強度試驗機，介電常數與介質損耗測試儀，電容率測試儀，體積表面積電阻率測試儀，低溫脆性沖擊試驗儀，維卡熱變形試驗儀，啞鈴制樣機，阿克隆磨耗試驗機，簡支梁沖擊試驗機，懸臂梁沖擊試驗機，熔體流動速率儀，無轉子硫化儀等。

安全注意事項：開機之前，敬請仔細閱讀本 使用指南，以防止出現對操作人員的意外傷害或對儀器的損壞等的事件。操作前，請閱讀“安裝與設置”，保證對儀器各部件的正確安裝與連接。在*次操作前，務必請有操作經驗的人員進行指導，防止誤操作造成意外事件的發生。電擊危險： 確保在安裝或維修該儀器之前使所有導線斷電，防止在帶電情況下，對人員或設備造成傷害。

Characteristic and application: Low temperature brittleness testing machine is used to determine the highest temperature of the sample when it is damaged by impact under specified conditions, that is, brittleness temperature. It can be used to compare the performance of plastics and other elastic materials under low temperature conditions. The brittleness temperature and low temperature properties of vulcanized rubber with different rubber materials or formulations can be determined. Therefore, it is indispensable not only in the quality inspection of scientific research materials and products, but also in the control of production process.

Applicable industry: It can be used to assess and determine the adaptability of electrical, electronic, automotive electrical appliances, materials and other products to storage and use in low temperature environment. It is suitable for schools, factories, military industry, research institutes and other units.

使用方法 1接通電源，溫控儀和計時器顯示燈亮。 2向冷井中注入冷凍介質（一般為工業乙醇），其注入量應保證夾持器的下端到液面的距離為75±10mm。 3將試樣垂直夾在夾持器上。夾的不宜過緊或過松，以防止試樣變形或脫落。 4按下夾持器，開始冷凍試樣，同時啟動時序控制開關（或按動秒表）計時。試樣冷凍時間規定為3.0±0.5min。試樣冷凍期間，冷凍介質溫度波動不得超過±1℃。 5提起升降夾持器，使沖擊器在半秒鐘內沖擊試樣。 6取下試樣，將試樣按沖擊方向彎曲成180°，仔細觀察有無破壞。 7試樣經沖擊后（每個試樣只準沖擊一次），如出現破壞時，應提高冷凍介質的溫度，否則降低其溫度，繼續進行試驗。 溫度，如這兩個結果相差不大于1℃時，即試驗結束。 

注意事項 1在試驗過程中不能切斷冷卻循環，否則會產生不制冷的效果。 2氣缸壓力在出廠前已調節好，不能任意變動。 

經營理念：一、誠信待戶 顧客至上     全心全意為顧客考慮，使顧客能切身感受到人性化的儀器。二、精準檢測 保質保量     精準檢測是我們的責任 保質保量是我們對客戶的鄭重承諾三、技術* 創新理念  儲備開發人才，引進*技術，采用先進的設計理念，打造精良的檢測儀器。

北廣產品廣泛應用于國防、大專院校以及檢測所等行業，本公司以技術的創新為企業的發展方向，以新型實用的產品引導客戶的需求。

在使用本機之前，請認真閱讀使用說明書，充分理解之后，再開機使用。請愛護本機，正確使用，以便使該機永遠保持較高的精度和良好的運行狀態。

北廣儀器綜合實力雄厚，技術水平*，售后服務完善。公司勤于市場發展需求，致力于打造產品生產、銷售一站式服務，頗受廠商歡迎，并且在全國極為，產品種類、型號等可根據客戶要求供應。

原始包裝：請保留所有的原始包裝材料，如果機器必須回廠維修，請用原來的包裝材料包裝。并請先與制造廠的維修中心聯絡。送修時，請務必將全部的附件一起送回，請注明故障現象和原因。另外，請在包裝上注明“易碎品”請小心搬運。

我們每個工作日都為數家合作商與直接用戶提供質優價廉的儀器設備！歡迎您成為北廣儀器的用戶！?

關于儀器貨期：本儀器是北廣儀器熱銷的單品之一，供應。當天確認訂單（下午五點前）當天發貨！下午五點后確認訂單的，隔日發貨！個別情況因為發貨量過大會出現斷貨現象，貨期約2-3天。如果您需要貼牌生產，由于貼牌標牌需要現產，貨期會適當延長。詳情請與客服溝通。

視頻指導培訓操作人員，使參訓人員能正常操作儀器、初步會判斷故障、簡單維護保養。

每年進行客戶回訪。

軟件升級：終生免費提供新版本控制軟件。

提供適用、詳細、全面的中文產品說明書和維修手冊。

結構原理

1. 升降夾持器

升降夾持器由帶有夾持器的氣缸和氣缸座組成。

從試樣受沖擊部位，到夾持器下端的距離為11.0±0.5mm。

2.沖擊裝置

沖擊裝置由沖擊器和沖擊氣缸組成。

3.沖擊器

沖擊器頭部形狀和尺寸如實物所示。沖擊器的重量為200±20g，其工作行程為40&plusmn;1mm。沖擊氣缸在復位狀態下，沖擊器端部到試樣的距離為25±1mm。

4.冷凍介質：工業乙醇

5.本測定儀器采用壓縮機直接致冷.不需要冷卻循環水。